Long
Water Pump
 |
Long
water pumps were used on most 1969 and later passenger cars and
1973 and later trucks. Check your application before ordering.
Water
Pump Dimensions PDF
|
 |
With the increasing
use of long water pumps on modified vehicles these are very popular.
Bolt to the top water pump and the two front intake bolts. May be
used individually or as a pair. Will clear tall valve covers. NO
DRILLING OR TAPPING REQUIRED. A hole is provided in the A.C. bracket
for a heater hose. Will Not Work With Vortec or Fast Burn Heads. Will Not Work With Air Gap Manifold.
Bracket
Dimensions
Bracket Requirements
|
Part#
|
Price |
101R
- A.C. |
116.00 |
201L
- ALt. |
103.50 |
Rear View
|
 |
Same as 101R and
201L, but for opposite sides. The A.C. bracket is often used in
conjunction with the factory alternator mount.Will Not Work
With Vortec or Fast Burn Heads. Will Not Work With Air Gap Maniflold.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
101L
- A.C. |
116.00 |
201R
- ALt. |
103.50 |
Rear View
|
 |
Similar to the
101R and 201L, these brackets move the compressor forward and
the alternator out to clear multiple carbs, etc. The compressor
belt runs in the groove normally used by the alternator and vice
versa.Will Not Work With Vortec or Fast Burn Heads. Will Not Work With Air Gap Manifold.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
103R
- A.C. |
116.00 |
203L
- ALt. |
103.50 |
Rear View
|
 |
A very versatile
street rod style bracket system. Works well with most induction
systems. Will clear multiple carbs, fuel injection, etc. Bolts
to the head and top water pump bolt holes. The alternator bracket
will fit all 1969 and newer heads. The A.C. Compressor bracket
fits all G.M aluminum heads including the fast-burn aluminum heads
and may be used on 1969 thru 1986 cast iron heads by drilling
and tapping one hole for the upper mounting point. Will clear
up to 3 in. tall center bolt valve covers when used on 1987 and
later heads. Will clear up to 3 3/4 in. tall valve covers when
used on 1986 and earlier heads.
Bracket
Dimensions
Bracket Requirements
|
Part#
|
Price |
130R
- A.C. |
113.50 |
230L
- ALt. |
113.50 |
|
 |
These
brackets are designed for 1987 and later cast iron heads including
the popular VORTEC heads. VORTEC heads use 5/16" intake bolts
that point straight down. Will clear valve covers up to 3 in.
tall.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
131R
- A.C. |
113.50 |
230L
- ALt. |
113.50 |
|
 |
This bracket system
is similar to our 130R and 230L, but sits about 1 in. higher to
clear valve covers up to 4 1/2 in. tall when used with 1986 or
earlier heads. Bolts to the heads and water pump. When the A.C.
Compressor bracket is used on heads with one bolt hole, they will
require drilling and tapping one hole for the upper mounting point.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
120R
- A.C. |
113.50 |
220L
- ALt. |
113.50 |
|
 |
Designed for cars
with low hood clearance -- Vettes, Camaros, etc. These brackets
work great on most vehicles with a wide engine compartment-Trucks,
50-60's cars, etc. These brackets bolt to the head and top water
pump bolt holes. The alternator bracket will fit all 1969 and
newer heads. The A.C. Compressor bracket fits all G.M. aluminum
heads including the fast-burn aluminum heads and may be used on
1969 thru 1986 cast iron heads by drilling and tapping one hole
for the upper mounting point.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
134R
- A.C. |
113.50 |
234L
- ALt. |
113.50 |
|
 |
These brackets
are designed for 1987 and later cast iron heads including the
popular VORTEC heads. VORTEC heads use 5/16" intake bolts
that point straight down.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
135R
- A.C. |
113.50 |
234L
- ALt. |
113.50 |
|
 |
These brackets
bolt to the water pump and exhaust. NO HOLES NEEDED in head. Furnished
with hardware to fit stock exhaust manifolds and most headers.
If used with headers the front tube must turn down enough to allow
access to the bolt hole in front of the second pipe as shown in
the side view.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
123R
- A.C. |
113.50 |
223L
- ALt. |
113.50 |
Side View
|
 |
This bracket works
well if you are adding a compressor to a long water pump application
and want to leave the alternator in the factory location on the
passenger side.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
119L
- A.C. |
113.50 |
Side View
|
 |
This bracket works
well if you are adding a compressor to a LONG water pump application.
Designed to bolt to the head and top water pump bolt only. Will
not work with factory power steering pump bracket, must use our
Part# 402L Power Steering Pump Bracket.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
137L
- A.C. |
113.50 |
|
 |
Low
Mount
Tight-fit design fits narrow frames. Compressor bolts to fuel pump
mounting flange for strength. May be driven off crank and fan pulleys
or crank pulley ONLY. REQUIRES USE OF REMOTE FUEL PUMP. Check our
dimension requirements before ordering.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
107R
- A.C. |
92.50 |
|
 |
Low
Mount
Mounts the alternator low on the driver's side. Bolts to block and
water pump for the stability needed when mounting the alternator
low with a long water pump.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
214L
- Alt. |
95.00 |
|
 |
Factory
Alternator Support Bracket
This bracket kit was designed to be used with the stock long pump
alternator mount. It eliminates the need for a mountinghole in the
head when using early heads on a later application.
Bracket
Requirements
|
Part#
|
Price |
219R
- Alt. |
38.50 |
|
 |
Mid-Mount
This bracket mounts the alternator just above the pump inlet. Bolts
to head and water pump. Works well in low hood applications or for
extra space for TPI fuel lines, etc. FITS LONG PUMP ONLY. This bracket
can also be used with engines that have no bolt holes in the heads
by using the optional 215RO below.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
215R
- Alt. |
60.00 |
|
 |
215R
Support Bracket
This
optional bracket kit allows the 215R to be used on engines without
a hole in the head. Bolts to water pump attachment points and back
of the alternator.
|
Part#
|
Price |
215RO
- Alt. |
38.50 |
|
 |
Power
Steering
This bracket bolts to the front of the block and water pump boss.
Mounts the pump in approximately the same position as the factory
bracket without using the head or exhaust bolts allowing the use
of headers. Works with most 1979 and earlier Saginaw pump applications.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
402L
- P.S. |
89.50 |
|
 |
Power
Steering (Type
II Saginaw)
This bracket is designed to be used with the metric G.M. remote
reservoir type II pump. Designed for street rod applications, it
sits high enough to clear most chassis parts and steering gears.
WILL NOT WORK WITH LOW PROFILE BRACKETS. Pump is driven off
the inner groove of a 3 groove crank pulley. Pump uses an aluminum
V-belt pulley available from us or other street rod suppliers.
Bracket Dimensions
Bracket Requirements
|
Part#
|
Price |
410L
- P.S. |
89.50 |
|
Alan Grove Components, Inc.
27070 Metcalf Rd.
Louisburg, KS. 66053
Phone:913-837-4368 Fax:913-837-5721
|