Home                     About Us                   Sales Policy

                                                

SHORT WATER PUMP

Chevrolet used short water pumps on all passenger car applications thru 1968 and trucks thru 1972 with the exception of Corvettes. Corvettes always ran short water pumps.

Water Pump Dimensions PDF

 

Street Rod
A very strong bracket system for Big Blocks.  Bolts to the heads and top water pump locations.  A.C. bracket is complete with idler assembly.  Will clear most valve covers. 

Bracket Dimensions

Bracket Requirements

Part# Price
104R - A.C. 98.00
204L - ALt. 85.00


Street Rod
Passenger Side Alternator Bracket.This Bracket is often used for more radiator hose space on vehicles not using air conditioning.

Bracket Dimensions

Bracket Requirements

Part# Price
204R - Alt. 85.00


Street Rod Extra Clearance
Designed for Tuned-Port injection Systems. They also work well with most induction systems - single carbs, multiple carbs, tunnel rams, etc.  Bolts to heads and water pump. Will clear most valve covers.

Bracket Dimensions

Bracket Requirements

Part# Price
121R - A.C. 99.50
221L - ALt. 99.50


Low Profile
Engineered for low hood applications.  Works great on any vehicle with a wide engine compartment - Trucks, 50-60's cars, etc.  Bolts to the heads and water pump.

Bracket Dimensions

Bracket Requirements

Part# Price
118R - A.C. 98.00
218L - ALt. 98.00


Low Profile
Same as 118R and 218L above except for opposite sides.

Bracket Dimensions

Bracket Requirements

Part# Price
118L - A.C. 98.00
218R - ALt. 98.00


1964-68 Chevelle
Bracket system is designed for big block Chevelles using the SHORT WATER PUMP only. Brackets bolt to top water pump bolt, two points on the outer cylinder head and two bottom holes of drivers side engine block. Will clear up to 3" tall valve covers.

Bracket Dimensions

Bracket Requirements

Part# Price
601L - Alt. & P.S. 180.00
118R - A.C. 98.00

View Instruction Sheet

Low Mount
Mounts the alternator low on the drivers side. A very strong lower bracket with a lot of adjustment. Check the dimension requirements before ordering.

Bracket Dimensions

Bracket Requirements

Part# Price
208L - Alt. 75.00


Low Mount
This bracket is designed to use the new smaller G.M. CS130 alternator with the mounting ear in the 2 o' clock position as shown in the important info. page of this web site.  It requires less space than the standard G.M. alternator used on our 208L bracket.

Bracket Dimensions

Bracket Requirements

Part# Price
210L - Alt. 75.00


Low Mount A.C.
Bolts to fuel pump mounting flange.  May be driven off crank and fan pulleys or crank pulley ONLY.  REQUIRES USE OF A REMOTE FUEL PUMP.  Check our dimension requirements before ordering.

Bracket Dimensions

Bracket Requirements

Part# Price
108R - A.C. 80.00


Power Steering
This Big Block bracket is designed for the Chevrolet Saginaw non - metric power steering pumps with the attached reservoir.  They allow clearance for the alternator belt no matter where the alternator is mounted.  These pumps were used on most Chevrolet applications with short and long water pumps until the early 1980's.  Short water pump applications are normally driven off an add - on third crankshaft pulley.  These pulleys are available from Chevrolet under Part Number 3751232 or from us.
Will not work with Chevelle use Part# 601L

Bracket Dimensions

Bracket Requirements

Part# Price
403L - P.S. 78.00

Rear View

Power Steering (Type II Saginaw)
This bracket is designed to be used with the metric G.M. remote reservoir type 2 pump. Designed for street rod applications, it sits high enough to clear most chassis parts and steering gears. WILL NOT WORK WITH LOW PROFILE BRACKETS. Pump is driven off the outer groove of a 3 groove crank pulley. Pump uses an aluminum V-belt pulley available from us or other street rod suppliers.

Bracket Dimensions

Bracket Requirements

Part# Price
413L - P.S. 78.00


Power Steering (Type II Saginaw)
This bracket is designed to be used with the metric G.M. remote reservoir type 2 pump. Designed for low profile bracket applications, it provides clearance for alternator belt no matter where the alternator is mounted. Pump is driven off the outer groove of a 3 groove crank pulley. Pump uses an aluminum V-belt pulley available from us or other street rod suppliers.

Bracket Dimensions

Bracket Requirements

Part# Price
415L - P.S. 78.00





Back to Top

Alan Grove Components, Inc.
27070 Metcalf Rd.
Louisburg, KS. 66053
Phone:913-837-4368 Fax:913-837-5721